The reason why the high-mounted brake light doesn't light up
The main reasons for the high-mounted brake light not lighting up include brake bulb failure, wiring issues, brake light switch failure, fuse blowout, and computer module failure in high-end models . It is necessary to check them in time to avoid potential safety hazards.
Common Causes and Analysis
Youdaoplaceholder0 Bulb failure : The filament is blown or the bulb is burned out. A bulb of the same specification needs to be replaced.
Youdaoplaceholder0 Circuit issues : If the circuit is damaged, broken or the plug is loose, it can be repaired by testing the light or using a multimeter.
Youdaoplaceholder0 Brake light switch fault : The switch is damaged, causing signal interruption and needs to be replaced.
Youdaoplaceholder0 Fuse blown : Excessive current causes the fuse to blow. It needs to be inspected and replaced.
Youdaoplaceholder0 computer module failure (high-end models) : The fault code storage needs to be reset by power-off or cleared by professional equipment.
When the fault light of the high-mounted brake light comes on, it usually indicates that there is an abnormality in the vehicle's braking system, which may be caused by worn brake pads, insufficient brake fluid, malfunction of the brake light switch, short circuit in the circuit or problems with the high-mounted brake light itself. Youdaoplaceholder0 immediate inspection is required to avoid potential driving safety hazards .
Analysis of Fault Causes
The high-mounted brake light fault light coming on is a warning signal of the vehicle's braking system. Common causes include:
Youdaoplaceholder0 brake system failure :
Severe wear of brake pads: When the brake pads wear to the limit, the induction wire automatically connects the circuit, triggering the fault light to come on.
Low brake fluid level or substandard quality: Insufficient brake fluid can lead to a decrease in braking force. When the sensor detects an anomaly, it will light up the fault light.
Brake system oil leakage: Aging of the gasket or damage to the oil seal can cause leakage, affecting braking performance and triggering an alarm.
Youdaoplaceholder0 brake light switch or circuit problem :
Brake light switch malfunction: Poor or damaged internal contact of the switch causes continuous signal transmission, keeping the high-mounted brake light constantly on.
Short circuit or open circuit: The vibration of the vehicle body causes the circuit to loosen and the insulation layer to be damaged, resulting in abnormal current.
Youdaoplaceholder0 fault of the high brake light itself :
Bulb burnout or lampshade damage: Aging or physical damage to the LED light source leads to abnormal circuits.
Electronic control system failure: ABS system failure or control module error, mistakenly sending a lighting signal.
Solutions and steps
According to the cause of the fault, the following measures can be taken:
Youdaoplaceholder0 preliminary self-check :
Check the brake fluid level: Open the hood to inspect the fluid reservoir. If the fluid level is below the MIN line, add the same type of brake fluid (such as DOT4) and identify the leakage point.
Observe the condition of the brake pads: If the vehicle is equipped with induction wires and the wear exceeds the limit, they need to be replaced. If there is no induction wire, listen to the "hissing" sound or measure the thickness (replace it immediately if it is less than 5 millimeters).
Confirm the status of the handbrake: Make sure the handbrake lever is fully in place to avoid accidentally triggering the warning light.
Youdaoplaceholder0 professional maintenance advice :
If self-inspection fails, it needs to be sent to a professional repair shop
Use diagnostic equipment to test the ABS system and electronic control module.
Check for short circuits or open circuits in the lines and repair damaged connection points.
Replace the damaged brake light switch or bulb.
Emergency handling: Pull over to the side of the road when the warning light is on to avoid sudden braking. If the pedal becomes soft or sinks, call a tow truck immediately.
Safety Precautions
Youdaoplaceholder0 Risk Warning : After the high-position brake light fault light is on, for every hour of delay in handling, the accident risk increases by 300%, which may cause an extended braking distance or complete failure.
Youdaoplaceholder0 preventive measures :
Regular maintenance: Check the brake pads every 30,000 kilometers and replace the brake fluid every two years.
Daily maintenance: Clean the dirt on the lampshade and avoid high-voltage interference (such as water scraping after frequent switching).
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAXUS auto parts welcome to buy.
