What is the lever at the left rear door of the car?
The left rear door lever of a car usually refers to the outer door handle of the right rear door, that is, the handle used to open the door from outside the vehicle. This term is not related to the suspension or steering system's "lever", but rather a component on the door.
What exactly is it referring to?
Location: On the outside of the rear left door, for passengers to open the door from the outside.
Common types: The most common type is the outward pull handle, which can be opened by simply pulling outward; there are also fixed type, up-reach type, etc.
Internal structure: The handle is linked to the door lock through a pull cord or linkage mechanism. When pulled, the lock tongue retracts to unlock the door.
Points to be confused:
"Pull rod" has multiple meanings in automobiles. Be sure to distinguish:
Suspension pull rod: Such as rear pull rod, balance pull rod, which belong to the chassis suspension system, used to support the vehicle body, control wheel alignment, and absorb impact.
Steering pull rod: Belong to the steering mechanism, transmitting steering motion and assisting steering.
Door limit stop pull rod: Installed at the door hinge, controlling the opening angle of the door to prevent it from sliding freely.
If it is said that the left rear door cannot be opened from the outside or the handle is loose, it is usually a problem with the external door handle or the internal pull cord, and checking the handle itself and the linkage mechanism is enough.
Pull rod of the left rear door's "external pull rod" usually refers to the mechanical linkage pull rod or pull cord inside the external door handle. Its core function is to transfer the force of pulling the handle to the door lock mechanism, thereby unlocking and opening the door.
When pulling the external handle, the pull rod moves and the lock tongue retracts, allowing the door to be opened; when the central lock locks, the pull rod disconnects from the lock mechanism, and pulling the handle from the outside will not open the door.
Specific functions:
Transmitting opening force: External handle → Pull rod → Lock mechanism → Lock tongue. This mechanical chain is the most basic opening method for traditional car doors. An adult can open it with one pull.
Mechanical safety redundancy: In extreme situations such as power failure or collision, even if the electronic unlocking fails, as long as the mechanical structure of the pull rod is intact, the door can still be manually opened from the outside. This is an important safety backup.
Locking linkage: When the central lock is locked, the pull rod disconnects from the lock mechanism, and pulling the handle from the outside cannot unlock the lock, preventing unauthorized opening from the outside.
Things to note:
If the left rear door cannot be opened from the outside, it may be that the pull rod is detached, loose, or the lock cable is broken. Usually, it is necessary to remove the door interior panel for inspection or replacement of the pull cord.
The left rear door may also have a "child lock". If the child lock is activated, it can only be opened from the outside and cannot be opened from the inside. This is a normal phenomenon rather than a fault.
The most common cause of failure of the left rear door's pull rod is that the pull rod is detached, broken, or the connection part is worn. The handling method depends on the specific degree of damage.
Don't rush to remove the door panel. Follow the steps below to troubleshoot and solve the problem yourself. If it can be resolved by yourself, skip the trip to the repair shop.
First, determine the type of failure:
Pull handle is loose but can open the door: Most likely, the connection at the pull rod is loose or the latch is aging. Remove the door panel and re-tighten it.
Pull handle cannot be pulled or the door cannot be opened: It may be that the pull rod is broken or the lock block is stuck. You need to remove the door panel to check the internal structure.
Pull handle can be pulled but the door does not respond: The pull rod is disconnected from the lock body, the pull handle shakes, and the lock body does not move. This is most likely a problem with this pull rod.
Self-repair steps:
Tools: T series flower-shaped wrench (T20/T25/T30), plastic pry bar, screwdriver, needle-nose pliers, flashlight should also be brought. The interior of the door cavity is very dark.
Remove the door panel: Unscrew the fixing screws on the door panel (usually at the external handle and the handle guard). Use the plastic pry bar to start prying from the bottom or the side of the door panel. Pay attention to the latch position and do not use brute force.
Check the pull rod condition: After removing the waterproof film, use a flashlight to observe whether the pull rod is broken, rusted, or detached. Pull the external handle to observe if the pull rod is linked to the lock body.
Handling methods:
Pull rod detached: Reattach the lock body linkage arm and ensure the latch head is tightly engaged. Otherwise, it will still detach.
Pull rod rusted, broken : Buy a new pull rod of the same model and replace it. After installation, the latch head must be firmly engaged.
Pull rod slightly deformed: You can try to correct it, but welding repair strength is not as good as the original factory. It is recommended to replace it directly.
Reinstalling the door panel: First, attach the inner handle pull cord and the electric glass connection wire. Then, apply the waterproof film, install the door panel, and finally test repeatedly to ensure smooth opening and closing of both the inside and outside doors.
Notes for Attention
When removing the door panel, the snap fasteners are prone to damage. It is recommended to gently pry and remove it slowly. If damaged, replace the snap fasteners. Otherwise, there will be abnormal sounds in the future.
When installing the new pull rod, it is suggested to apply a small amount of low-temperature resistant lubricating grease at the movable joint to extend the service life.
If the pull wire is also worn or stretched deformed, it is recommended to replace it together to avoid rework in the short term.
Before starting the work, make sure the central locking has been unlocked to avoid misjudging it as a pull rod fault, which could actually be a problem with the lock block or the central locking motor.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAXUS auto parts welcome to buy.