What is the lower mounting bracket for the car rear guard panel?
The lower mounting bracket of the car rear guard - This is a key structural component for fixing the rear guard (or the lower part of the rear bumper) to the vehicle body. It mainly serves the functions of supporting, fixing and buffering.
What exactly is it?
It is a metal or high-strength plastic bracket located at the lower part of the vehicle's rear, connecting the guard plate and the vehicle's frame. Usually, there is one on each side, hidden beneath the trunk or inside the bumper. When installing the guardrail, the bracket is aligned with the reserved screw holes on the original vehicle's impact bar and fixed to ensure that the guard plate does not loosen or tilt.
Main function
Fixed support: Secure the rear guard plate firmly to the vehicle body to prevent loosening, abnormal noise or sagging during driving.
Collision buffer: Absorb and distribute the impact force in a rear-end collision, reduce damage to the vehicle structure, and protect the safety of passengers.
Maintain appearance: Ensure that the gap between the guard plate and the vehicle body is uniform, avoid skewing, and prevent any impact on the overall appearance of the vehicle.
Q&A
When the bracket is damaged, the rear guard plate will droop, make a creaking sound as it passes the speed bump, or have an uneven gap with the vehicle body. If these issues are detected, it is recommended to promptly repair and replace the bracket instead of compromising.
The materials of the brackets for different vehicle models vary. Ordinary cars mostly use steel plates, while high-end cars may use aluminum alloys, and some even have buffer devices.
The main function of installing brackets at the lower part of the car guard plate is to fix and support the guard plate, and to transfer and disperse the collision impact force. At the same time, it can also make the installation of the guard plate more stable and prevent loosening or abnormal sounds during driving.
Specifically, its functions can be divided into the following:
Fixation and support: Firmly fix the guard plate on the vehicle body to prevent it from shaking or falling off due to vibration or wind resistance during driving, and it is also convenient for disassembly during future maintenance.
Transmission and dispersion of impact force: In case of rear-end collision or bumping, the bracket can conduct the impact force to the vehicle frame, reducing direct damage to the rear parts and the vehicle body, equivalent to adding a buffer layer to the rear of the car.
Prevention of guard plate drooping: The guard plate has a certain weight, and the bracket combined with the hook structure can overcome the weight-induced drooping, avoiding interference between the guard plate and the rear bumper installation path, ensuring smooth assembly.
Enhancement of vehicle body rigidity: Installing the bracket can increase the local structural strength of the car tail, which is helpful for driving stability and torsion resistance.
If the bracket is aging, damaged, or not installed properly, the guard plate may loosen, produce abnormal sounds, and fail to provide the expected protection during a collision, so it is recommended to check or replace the guard plate along with the status of the bracket when inspecting or replacing it.
The most common cause of faults in the lower part of the car guard plate installation brackets is loose fasteners, aging plastic snap fasteners, or rust and deformation of the bracket itself, causing the guard plate to shake, produce abnormal sounds, or even fall off.
First, determine the type of fault
Driving abnormal sound: A "clunking" or "creaking" sound when driving over bumpy roads, mostly due to loose fasteners or too small a gap between the guard plate and the chassis components causing friction.
Guard plate shaking or loosening: When gently pushed, the guard plate has a loose feeling, usually due to the fracture of the fixing snap or the failure of the bracket bonding points.
Rust or fracture of the bracket: The metal bracket is corroded and deformed due to long-term moisture, its strength decreases, and it breaks easily when pinched, requiring direct replacement.
Solution for handling the issue
Fastening screws: Check all fixation points. For loose ones, tighten them in a diagonal sequence in 2-3 steps. The torque should refer to the maintenance manual (usually 20-30 N·m).
Adding buffer pads: Add 2-3mm rubber gaskets or vibration damping stickers at the screw positions and the contact surfaces between the guard plate and the bracket to separate the hard contact and solve most resonances and abnormal noises.
Replacing clasps or brackets: If the clasps are aged and broken, replace them with new ones (original factory or high-strength nylon material, about 10 yuan each); if the brackets are severely rusted, find the original vehicle parts or compatible replacement parts.
Adjusting installation position: When the guard plate is installed crooked or interferes with the exhaust pipe or suspension, reposition and install it to avoid continued friction.
If the deformation area of the guard plate is large, the screw hole positions are misaligned by more than 5mm, or there are tear marks, it is recommended to replace it directly. Forcing it to be flat will cause uneven stress, and it will be more prone to problems in the future.
Special reminder
The bracket failure should not be postponed for a long time. The screws may completely come off. The guard plate may be blown over and scraped against the ground at high speed, or even get caught in the transmission shaft, posing safety risks.
Using zip ties for temporary fixation is only an emergency measure. They will become brittle due to heat and break down in about 3 months. The fixed force is uneven, which can easily cause new noises. The proper way is to replace with snap fasteners.
If the guard plate was added later, first confirm whether it is a dedicated part for the vehicle. If the common part hole position is incorrect, forcing the installation is more likely to cause loosening.
Most problems can be solved by yourself in half an hour and at a cost of several dozen yuan. If unsure, go to the repair shop. Let the technician lift and inspect first. Don't just keep tightening the screws blindly.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAXUS auto parts welcome to buy.