What is the car washing jug assembly?
The car washing jug assembly is the liquid storage and supply part of the car windshield cleaning system, responsible for storing windshield washer fluid and delivering it to the spray nozzle through the washing pump, cooperating with the wiper to clean the front windshield. It is generally composed of a jug body, a filling pipe, a washing pump (motor), a pipeline, and a spray nozzle.
Main Components and Functions
Jug Body: The main container for storing windshield washer fluid, usually installed in the engine compartment, with mounting feet and support seats, fixed to the vehicle structure to resist vibration.
Filling Pipe Assembly: Connects the mouth of the jug body with the filling port on the engine compartment decorative panel, facilitating the daily replenishment of windshield washer fluid, with a focus on sealing and connection reliability.
Washing Pump (Spray Motor): A small motor installed at the bottom or side wall of the jug body, which, after being activated, rotates the impeller to pressurize the windshield washer fluid and deliver it, being the key component determining the spray function.
Pipes and Spray Nozzle: Transfers the pressurized windshield washer fluid from the pump to the spray nozzle in front of the windshield, spraying it onto the glass surface.
Q&A
The damage of the washing pump is a common fault, manifested as the motor not making any sound or not spouting water when the water spray switch is toggled, even if there is water in the pot.
The leakage of the interface between the filling tube and the pot body is due to poor sealing, which causes liquid leakage and affects normal use. This is also the key direction for the improvement of related patents.
The core function of the car washing pot assembly is to store water for the windshield and pump the water through the washing pump to the nozzle, spraying it onto the windshield to cooperate with the wiper to clean the view. It directly relates to the safety of vision during driving in rainy, dusty or muddy sections.
Component composition and division of labor
Washing pot (storage tank): Usually a plastic tank of 1.5 liters to 2 liters, used for storing water for the windshield.
Washing pump / water spray motor: Installed at the bottom or side wall of the pot, it is the core power component. It is driven by an internal permanent magnet DC motor to rotate the impeller and pump the water under pressure.
Piping and nozzle: The water supply pipe conveys the pressurized water to the water spray nozzle on the front windshield or rear window, and the water is squeezed into fine jets by 2 to 4 nozzles and sprayed out.
Work process
After pressing the washing button on the switch when it's raining, the washing pump starts, pumping the glass water from the tank and delivering it through the pipeline to the nozzle, spraying it onto the glass. The rain wiper then scrapes off dust, dirt, bug glue and other stains.
If the washing pump fails, even if there is a lot of glass water in the tank, it cannot be pumped out. The rain wiper can only scrape dry, and the vision will be greatly affected.
Common Faults and Maintenance
Weak water spraying or no water spraying: This is mostly caused by worn carbon brushes of the washing pump, blocked pipelines or blocked nozzles. You can check the pipelines and nozzles, and replace the pump if necessary.
Abnormal noise or non-functioning motor: This may be due to worn carbon brushes and rotors inside the motor. This is a normal wear-out phenomenon after long-term use.
Selection Tips: The installation method and interface of the washing pump may vary for different car models. When replacing, it is recommended to choose a model that matches the car model to avoid improper installation.
Fault Diagnosis Steps
First, check the basic supply: Confirm the liquid level of the glass water. If it's low, add water directly. If it's winter and you use non-freezing glass water, the freezing in the tank may cause the motor to run idle or even damage, so you need to thaw it before testing.
Then, check the fuse: Open the engine compartment or the driver's side fuse box, find the fuse labeled "WASH" or "WIPER", and check if the metal wire is melted. If it is melted, replace it with a new fuse of the same specification (usually 10A or 15A). If it melts again after replacement, be alert for a short circuit.
Check the circuit connection: Unplug the motor plug, use a multimeter or 12V test light to measure the voltage. When operating the water spraying switch, there should be about 12V voltage. If there is voltage but the motor does not turn, it is likely that the motor is damaged; if there is no voltage, check the switch and relays.
Check the pipelines and nozzles: If the motor makes noise but does not spray water, it is mostly due to a blocked nozzle or pipeline problem. Use a fine needle to gently clear the nozzle hole, check if the rubber hose is bent, cracked or detached, and also pay attention to whether the filter in the water tank is blocked by impurities.
Test the motor body: If the power supply and fuse are normal, you can directly connect a 12V power supply to test the motor. It can turn but is weak, which may be due to worn carbon brushes; if it does not turn at all, it is confirmed that it needs to be replaced.
Common Fault Handling
Motor damage: Replace the new motor. Different car models have differences in interface, positioning and sealing structure. When purchasing, provide the vehicle frame number or production year for verification. When installing, ensure that the sealing ring is tightly attached to prevent water leakage.
Glass water tank damage: The glass water tank is prone to cracking due to collision and squeezing, especially when hitting the curb while driving. The most common leakage is from the sealing ring, and the bottom leakage is due to the cracking of the tank. You need to replace the new part, and the price is usually around 100 yuan.
Tank freezing and cracking: In the northern winter without using anti-freezing glass water, the expansion of ice will crack the tank, and it can only be replaced, not repaired.
Preparation for Maintenance
Before conducting maintenance, disconnect the negative terminal of the battery to ensure safety. The water spraying time should not exceed 5 seconds to avoid overheating of the motor; during daily use, add special glass water regularly, do not use tap water instead, to avoid water scale damage to the motor.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAXUS auto parts welcome to buy.