What is the sealing plug for the right front door of the car?
The right front door seal plug is a small rubber/TPE cover installed on the door or body hole. It is mainly used for sealing, windproofing, dustproofing and waterproofing. At the same time, it also serves as a buffer and shock absorber, preventing the door from deforming.
It is usually placed in small round holes reserved on the lower edge of the door, the chassis maintenance opening, and the wire harness holes during production to prevent dust, rain, fallen leaves, and even small insects from entering the interior of the door. It can also avoid abnormal sounds caused by direct metal collision when closing the door.
Specific functions
Sealing protection: Blocks wind, rain and dust, preventing the inner side of the door from getting damp, the foot mat from getting wet or developing a musty smell.
Buffer and shock absorption: Reduces impact when closing the door, reduces sheet metal vibration and noise, and is less likely to deform over time.
Protecting the interior: Prevents water vapor from invading and damaging the seats, electronic equipment, etc.
Attention
Don't remove or lose it at will. If you find that the sealing plug is aging, loose or fallen off, it is recommended to replace it with a plug of the same size in time.
After washing the car, you can check it yourself. If it is loose, just press it tight. It only takes a few seconds.
The main function of the sealing plug on the right front door of the car is to seal, prevent wind, dust and water. At the same time, it can also play a role in buffering and vibration reduction.
Specific functions
Sealing and leak prevention: Fill the gap between the car door and the body, prevent rain, dust from entering the car, and also prevent water from entering the cavity of the inner panel of the car door.
Buffer and vibration reduction: Reduce the impact of the car door on the body sheet metal when closing, reduce the vibration of the car door when driving on bumpy roads, and prevent long-term collision between iron and iron from causing the car door to deform and the gap to widen.
Noise reduction and insulation: Reduce the transmission of wind noise and external noise into the car, and help maintain the air conditioning effect inside the car, keeping it warm in winter and cool in summer.
Attention
The sealing plugs or buffer rubber blocks should not be removed. If they are missing, when closing the door, the metal parts collide with each other, and over time, the car door is prone to deformation and the noise increases.
If you find that the sealing plug on the right front door is aging, cracking or falling off, it is recommended to replace it in time. Generally, choosing products made of EPDM rubber from a reputable manufacturer is more durable.
If the right front door sealing plug malfunctions, it usually means that the door sealing strip is aging, damaged or not installed properly, causing air leakage, water leakage or abnormal noise.
First, follow these steps to troubleshoot. Most problems can be solved by yourself without rushing to the repair shop to replace the entire set.
Confirm the type of fault
Air leakage or loud wind noise: When driving at high speed, there is a "sizzling" sound near the right front door. Don't blame the sealing strip. It might be that the triangular decorative plate of the rearview mirror base is loose, and the wind is coming in through there. Fold the rearview mirror and drive for a while, and the wind will significantly decrease. The problem lies in the rearview mirror base, not the sealing strip of the door.
Water leakage or wet floor mat: It is likely not due to the aging of the sealing strip, but the blockage of the drainage hole at the bottom of the door. Leaves, mud and sand form a film, and the rainwater cannot be drained away, and when the water level is high, it seeps into the car.
Difficulty closing or not closing tightly: It might be that the sealing strip is deformed, the door hinge is sinking, or the position of the door lock seat is off. It is not necessarily a problem with the sealing strip itself.
Abnormal noise when opening or closing the door: The friction sound caused by the aging and hardening of the sealing strip, or the lack of oil in the door hinge can be solved by adding some lubricating oil.
Carry out troubleshooting and repair
Check the drainage hole: Slowly pour water into the car window glass with a mineral water bottle and observe if the water flows out smoothly from the drainage hole at the bottom of the door. If the water flow is thin, intermittent or does not come out, it is blocked. Use a fine iron wire or cable tie to gently push and flush it again. It is likely to be resolved.
Check the sealing performance of the sealing strip: Place an A4 sheet between the door and the door frame and close the door. Pull it out. If it moves smoothly with almost no resistance, it indicates that the sealing at that position is not tight. Test several points along the upper edge, B-pillar, and lower edge of the door frame to find the leakage location.
Check the condition of the sealing strip: Feel it with your hand. If it becomes hard, cracks, loses elasticity, or partially falls off, it needs to be dealt with.
Slight detachment, not aging: Apply 401 glue or 3M double-sided adhesive to the peeled area, press it from top to bottom and fix it. Make sure to clean the car door's metal surface and dry it before applying the glue, otherwise it may not stick well.
Severe aging, cracking, and hardening: Don't repair it. Replace it directly. Choose the original factory specification or EPDM material, clearly stating the model, year, left and right front positions. Don't buy the wrong model.
Check the door hinge and lock mechanism: If the door does not close tightly or is misaligned, check if the hinge screws are loose and if the lock seat is worn. Loosen the fixing screws of the door lock, adjust the position to make the lock tongue accurately bite, and the door will close tighter and the noise will be smaller.
When clearing the drainage hole, do not use hard objects like iron wires to forcefully push, to avoid breaking the hose; avoid frequent opening and closing of the door within 24 hours after the sealing strip is bonded.
After troubleshooting for half an hour by yourself, clean what can be cleaned and replace what can be replaced. It is much more convenient than directly going to the repair shop. If the door is deformed due to a collision and causes poor sealing, do not try to fix it yourself. Find a professional sheet metal worker to handle it.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAXUS auto parts welcome to buy.