How to clean the heat insulation layer at the rear of the car?
The automotive rear window insulation layer usually refers to the heat insulation film (also known as solar film or sunshade film) in the rear windshield or rear window area. Its cleaning requires special attention to protecting the heating lines (used for rear window defogging) and possible radio antennas. According to the latest publicly available information, the recommended operation steps are as follows:
Cleaning steps
Preparations
Tools needed: plastic scraper (or old credit card), hair dryer/air blower, rubbing alcohol/ethyl alcohol/ specialized desoldering agent, clean soft cloth, water.
Environmental requirements: Operate in a well-ventilated area to avoid uneven heating of the glass due to direct sunlight.
Unfold the corner of the film
First, try to use your fingernail or tape to stick up one corner of the film; if ineffective, use a knife blade to make a very gentle cut (but be sure to control the angle (close to the glass)) to prevent scratching.
Heat air assistance for film removal
Use the hair dryer (set to medium temperature, 15–20 cm away from the glass) to evenly heat the film surface to soften the adhesive layer.
Key point: The heating lines on the rear windshield are dense, do not heat the same area for a long time, move the heat air slowly along the edge.
Slowly remove the insulation film
Start from the lifted corner and pull it at a 15°–30° small angle at a uniform speed, drip a little rubbing alcohol or desoldering agent to assist in breaking the adhesive.
Clean up residual glue stains
After removing the film, there are often glue stains on the glass. You can choose any of the following methods:
Special desoldering agent: Spray on the glue surface, let it stand for a few minutes to soften, then use a plastic scraper to scrape off in one direction.
Rubbing alcohol/ethanol: Apply after waiting for softening, then use a soft cloth or scraper to gently wipe.
Soap water or white vinegar water: Suitable for mild residues, soak and then clean with a soft brush.
Do not use steel wool, knife blades, etc., as sharp tools, to avoid damaging the heating lines or the glass.
Finishing and ventilation
Wipe the glass with water to remove the residual cleaning agent.
Open the car door and window, ventilate and dry for several hours to eliminate the glue smell.
Notes
Special characteristics of the rear windshield: The heating lines on the rear windshield are very fragile. Any scratching may cause a break in the circuit, affecting the defogging function.
If you are not sure about the operation, it is recommended to go to a professional car beauty shop for handling to avoid damaging it.
The term "automotive rear window insulation layer" is not commonly used in automotive engineering terminology. Based on publicly available information and industry common usage, there may be the following two interpretations:
Interpretation one: refers to "rear windshield heat insulation film" (i.e., rear film)
If the actual referred to is the heat insulation film attached to the rear windshield (often mistakenly called "rear surround insulation layer"), its functions are as follows:
Privacy protection: Blocks outside views, reduces the risk of being spied on, and lowers property risks.
UV protection: Filters 99% or more of ultraviolet rays, reduces damage to skin and aging of interior materials.
Heat insulation and cooling: Reflects or absorbs part of infrared heat, reduces the temperature of the car interior in summer, and reduces the load on the air conditioning.
Safety and explosion prevention: The film layer has adhesiveness, and when the glass breaks, it can prevent fragments from flying, reducing secondary injuries.
Anti-glare: Reduces glare from strong light, improves driving comfort and safety.
Note: The rear windshield usually has electric heating wires for defogging. When applying the film, use a dedicated film and have it installed by a professional to avoid damaging the heating wires.
Interpretation two: refers to "heat insulation material" on the vehicle structure (such as heat insulation plates)
If it refers to the heat insulation material installed between the engine compartment and the passenger compartment, or near the exhaust pipe, its functions include:
Heat transfer blocking: Prevents high-temperature heat from being conducted to the interior, improves passenger comfort.
Protecting components: Reduces the aging risk of electronic components, wiring, etc. in the engine compartment due to high temperature.
Noise reduction effect: Some heat insulation materials also have sound absorption properties, reducing noise transmission into the cabin. If the problem is related to vehicle modification or window film application, "rear bumper insulation layer" is most likely referring to the rear windshield film.
If it involves engine compartment or chassis insulation, it might refer to insulation boards or heat shielding materials.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAXUS auto parts welcome to buy.
